LEVC - 3 Phase CEE Charging Cable. 16A 400V 11kW. Variable Amp - 8A, 10A, 13A, 16A. Type 2

Type 2 LEVC 3 Phase 400V 11kW CEE charging cable. Variable 8 amps, 10 amps, 13 amps and 16 amps

Charge your Type 2 LEVC EV using a 16A 3 Phase 400V CEE socket. 3 Phase 16A Type 2 to CEE charging cable that connects to the red 3-phase CEE / Commando sockets located in places such as industrial units, office buildings and marinas. Please check your 3 Phase (red) CEE socket before buying this charger, to make sure that it is the correct amp rating. The 16A 3 Phase CEE plug is not compatible with the 32A 3 Phase CEE socket. Click here if you require the 3 Phase 400V 32A 22kW CEE charging cable. These CEE chargers include an EVA cable carry case for storing the charger and a 1 year warranty.

The CEE plug provides a charge of up to 11kW, dependent on the onboard charging capacity of your vehicle. Even if your vehicle charges single phase 3kW or 7kW, this charger will provide the correct amount of current to your vehicle. Please make sure that the outlet is protected by a circuit breaker. Please make sure that the device is connected directly to the CEE socket and is not connected to an adapter or extension lead. Please ensure that the socket where you charge your vehicle is certified by a qualified electrician to ensure that the power outlet and circuit is suitable and safe for regular EV charging and is protected against the causes of overheating. Please note that this charger is not manufactured by LEVC, so although this product is a compatible LEVC charger, we always recommend checking your vehicle handbook.

This charging cable is compatible with the vehicles below. This list is updated so if you do not see your vehicle, please check your handbook or check that your vehicle socket matches the images above:

LEVC TX, LEVC TX5, LEVC LCV

Multiple safeguards are built in with this LEVC portable charger to protect against damage to the vehicle, outlet and charger whilst charging:

• PCB Temperature Sensor
• Earth Fault Monitoring
• Leakage Protection
• Overcurrent Protection

• Overvoltage Protection
• Undervoltage Protection
• Lightning Protection
• Water Resistant

This LEVC CEE 3 Phase charging cable has adjustable current and a delayed charging timer that allows charging to begin between 1 to 10 hours after the Commando and Type 2 plugs have been plugged in. The charger can be used with a 5 pin 16A 380V - 415V CEE / Commando socket and complies with the IEC 62752 standard for charging the Type 2 socket range of electric vehicles. The built in 30mA AC detection and 6mA DC detection (Type B protection) means that this 16A Commando charger can be used with a circuit protected by the minimum Type A or F RCD. The unit also has a bracket that will allow it to be mounted on a wall indoors.

What is variable charging?

This portable charger can adjust the current, enabling faster charging at 3 Phase 16A or slower charging at 8A, dependent upon the Onboard charger of your EV or PHEV. Therefore, if your vehicle is single phase or 3 Phase and accepts 3kW, 7kW, 11kW, this charger will provide the correct current. The charger will automatically stop charging the battery of your electric vehicle once it has reached the required charge setting or when it is fully charged.

The length it will take to recharge the battery for your LEVC hybrid / electric vehicle will depend on the battery that your LEVC is equipped with. Using your socket to charge regularly over long durations can cause thermal damage if the socket / wiring is not suitable.

Charging cable checklist

To ensure that the cable you purchase is right for you, please read the following checklist:

• Make sure the charging cable is compatible with your vehicle. The photos at the top of the page show you what the pins in the connectors look like so you can match the cable to your vehicle.
• Make sure that the length of the cable is sufficient to reach the charging socket of your vehicle. We recommend allowing at least half a metre so that the cable is not overstretched.
• Please check whether the CEE socket for the CEE plug is suitable for this charging cable. A 1-phase CEE socket has 3 holes. A 3-phase CEE socket has 5 holes. Your CEE socket must also match the amperage of the CEE plug. This information can usually be found on the cover of the CEE socket. If you are not sure, please send us a photo of your socket and the socket cover.

If in doubt, please contact us via our contact page.

How to use the variable 16A 3 Phase charger

Please read the safety information in the user manual included with this charger before using it. If you do not receive this information, please contact us. Using this Commando socket charger is straightforward and the instructions are also available in the user booklet. Simply plug the device into into the CEE outlet to power the device. The display will light up. The required ampere setting can be selected by clicking the amp button. Select the ampere setting to match your power outlet. The timer setting can also be set at this point. Connect the vehicle charging plug to your LEVC. After 1 minute or once you plug the EV connector into the car, the setting is 'locked in' and will be remembered the next time you use it. To change the setting, repeat the above procedure. Your vehicle software will communicate with the device and only draw the maximum amount of power that the battery can accept.

If you would like a Mode 3 charger that connects from a charging station to your EV, browse our range of Type 2 charging cables.

For trade enquiries or bulk purchases please contact us for a quote on our Trade Enquiries page.